- Manuals
- Brands
- Kwikset Manuals
- Locks
- 264
- Installation and user manual
Electronic deadbolt
Hide thumbs
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Parts in the Box
-
Required Tools
-
Prepare the Door and Check Dimensions
-
Install the Latch and Strike
-
Prepare Keypad and Mounting Plate (Only for Doors with Smaller Holes)
-
Install the Exterior Assembly
-
Install Interior Assembly
- Enter Door Handing Code and Test Lock
- Programming
- How to Change Your Programming Code
-
How to Add User Codes
-
How to Delete Individual User Codes
-
How to Add a One-Time User Code
-
How to Enable/Disable Auto-Lock
-
How to Change Auto-Lock Time Delay
- How to Restore Default Settings
-
System Alerts
- Troubleshooting
-
Important Safeguards
-
Regulatory Compliance
Advertisem*nt
Quick Links
- 1 Enter Door Handing Code and Test Lock
- 2 How to Change Your Programming Code
- 3 Programming
- 4 How to Add User Codes
- 5 How to Restore Default Settings
- 6 Troubleshooting
- Download this manual
ENGLISH
66101 / 01
Required tools
Ruler
Phillips
screwdriver
Batteries (4 AA)
Additional tools
(depending on application)
Pliers
Hammer
Wood block
Kwikset: 1-800-327-5625 • www.kwikset.com
264 Electronic Deadbolt
Parts in the box
Latch
Drive-in collar
A
B
Mounting plate
Interior assembly
G
H
Strike
Exterior assembly
D
C
Latch and
Interior cover
strike screws
J
K
1 / 10
Installation and User Guide
Cylinder
Keys
E
F
Mounting
Interior
plate screws
assembly screws
L
M
© 2016 Spectrum Brands, Inc.
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for Kwikset 264
-
Locks Kwikset 275 Installation And User Manual
Touchscreen electronic deadbolt (4 pages)
-
Locks Kwikset Deadbolt Series Quick Installation Manual
(2 pages)
-
Locks Kwikset 24896/04 Manual
(2 pages)
-
Locks Kwikset Powerbolt 240 Installation And User Manual
Keypad electronic lock (4 pages)
-
Locks Kwikset Powerbolt 250 Installation And User Manual
Keypad electronic lock (8 pages)
-
Locks Kwikset Henley 300HYL 15 Installation Manual
(4 pages)
-
Locks Kwikset SmartCode 913 Installation Manual
Touchpad electronic deadbolt (21 pages)
-
Locks Kwikset SmartCode 912 Programming And Troubleshooting Manual
(12 pages)
-
Locks Kwikset Smartcode 914 Programming And Troubleshooting Manual
(17 pages)
-
Locks Kwikset SmartCode 914 User Manual
(26 pages)
-
Locks Kwikset SmartCode 909 Installation And User Manual
Touchpad electronic deadbolt (6 pages)
-
Kwikset Smartcode 916 Programming and Troubleshooting Guide
(article)
-
Locks Kwikset 905 Installation And User Manual
Keyless entry touchpad deadbolt (4 pages)
-
Locks Kwikset HALO Installation And User Manual
Wi-fi touchscreen smart lock (4 pages)
-
Locks Kwikset Aura Installation And User Manual
Bluetooth keypad smart lock (4 pages)
-
Locks Kwikset SmartCode 913 Installation And User Manual
Tuochpad electronic deadbolt (4 pages)
Summary of Contents for Kwikset 264
- Page 1 Installation and User Guide ENGLISH 66101 / 01 264 Electronic Deadbolt Required tools Parts in the box Ruler Latch Drive-in collar Strike Exterior assembly Cylinder Keys Phillips screwdriver Batteries (4 AA) Mounting Latch and Additional tools Mounting plate Interior assembly...
- Page 2 Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep. Measure to confirm that the hole in the door Measure to confirm that the backset is is either 2-1/8"...
- Page 3 Install latch in door with bottom of latch. Proceed to next step. shown to extend latch. wood block and hammer. 180° K (2x) Make sure cross-shaped hole is at bottom of latch. Kwikset: 1-800-327-5625 • www.kwikset.com 3 / 10 © 2016 Spectrum Brands, Inc.
- Page 4 Proceed to step 4. 1. Remove gasket. 2. Remove adapter 3. Reinstall gasket, ring from gasket. ensuring tight seal. Use pliers to remove two tabs from mounting plate: Kwikset: 1-800-327-5625 • www.kwikset.com 4 / 10 © 2016 Spectrum Brands, Inc.
- Page 5 Remove the key and make sure the latch supplied screws. smooth operation. bolt is still in the unlocked position. Keep If latch does parallel to not operate door edge. smoothly, adjust screws. unlocked M (2x) Kwikset: 1-800-327-5625 • www.kwikset.com 5 / 10 © 2016 Spectrum Brands, Inc.
- Page 6 If turnpiece doesn’t rotate, repeat steps 5E and 5F, making sure to rotate L (3x) the turnpiece AWAY from the unlocked door edge. Kwikset: 1-800-327-5625 • www.kwikset.com 6 / 10 © 2016 Spectrum Brands, Inc.
- Page 7 Enter door handing code and test lock While the door is OPEN and UNLOCKED, enter the following code If successful, the Kwikset button will flash green 2 times and you to teach the lock the orientation of the door: will hear 2 beeps. If unsuccessful, the Kwikset button will flash red 3 times, and you will hear 3 beeps.
- Page 8 Before any programming sequence, make sure that your door is open and unlocked. For all programming sequences below, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.
- Page 9 1. Press and hold the Reset button for 5 seconds, until you hear orientation of the door: 3 beeps and see the Kwikset button flash amber 3 times. 4. Test the lock: WIth the door open and unlocked, press the Kwikset button to make sure it locks the door.
- Page 10 3 times with 3 beeps*. Codes are disabled. re-enable User Codes. If needed, restore the lock’s default settings. See When the door is closed and the Kwikset button is page 9. pressed to lock the door, the lock emits a system Attempt programming procedure Unsuccessful programming.
